Support Industrielle sensorer
Support Explosion Protection
Ultrasonic sensor UC500-18GS-IUEP-IO-V15
- IO-Link Interface for process data, parameterization and diagnosis
- Programmable via DTM with PACTWARE
- Programmable via IrDA (infrared interface)
- Selectable sound lobe width
- Synchronization options
- Enhanced temperature compensation adjustable, stable measuring values already 2 min after switching on
- Push-pull output
- Analog output
Please note: All product-related documents, such as certificates, declarations of conformity, etc., which were issued prior to the conversion under the name Pepperl+Fuchs GmbH or Pepperl+Fuchs AG, also apply to Pepperl+Fuchs SE.
Uddrag af datablad: Tekniske data for UC500-18GS-IUEP-IO-V15
| Produkt beskrivelse |
|---|
| Single head system |
| General specifications | ||
|---|---|---|
| Sensing range | 30 ... 500 mm | |
| Adjustment range | 50 ... 500 mm | |
| Dead band | 0 ... 30 mm | |
| Standard target plate | 100 mm x 100 mm | |
| Transducer frequency | approx. 300 kHz | |
| Response delay | minimum : 20 ms factory setting: 40 ms |
|
| Sensor cycle time | ≥ 10 ms (factory setting) ; programmable to 60 s |
|
| Temperature influence | with temperature compensation: ≤ ± 0.75% of the end value 10 min after switching on the sensor (factory setting) with enhanced temperature compensation: ≤ ± 0.75% of the end value 2 min after switching on the sensor without temperature compensation: 0.17 %/K |
|
| Memory | ||
| Non-volatile memory | EEPROM | |
| Write cycles | 300000 | |
| Indicators/operating means | ||
| LED green | solid: power on flashing: standby mode or IO-Link communication |
|
| LED yellow | solid: object in evaluation range flashing: switch point programming, object detected |
|
| LED red | solid: error flashing: switch point programming, object not detected |
|
| Electrical specifications | ||
| Operating voltage | 10 ... 30 V DC , ripple 10 %SS | |
| No-load supply current | ≤ 60 mA | |
| Power consumption | ≤ 1000 mW | |
| Time delay before availability | ≤ 300 ms | |
| Interface 1 | ||
| Interface type | IO-Link (via C/Q = Pin 4) | |
| IO-Link revision | 1.1 | |
| Device profile | Smart Sensor Profile 2 | |
| Process data width | 32 bit | |
| Device ID | 0x300602 (3147266) | |
| Transfer rate | COM2 (38.4 kBit/s) | |
| Min. cycle time | 3 ms | |
| SIO mode support | yes | |
| Compatible master port type | Class A Class B (use 3-pole adapter or 3-wire cable) |
|
| Interface 2 | ||
| Interface type | IrDA (infrared interface) | |
| Mode | point-to-point connection | |
| Transfer rate | 115.2 kBit/s | |
| Maximum communication distance | 5 cm | |
| Input/Output | ||
| Input/output type | 1 synchronization connection, bidirectional | |
| 0 Level | 0 ... 1 V | |
| 1 Level | 2.5 V ... UB | |
| Input impedance | > 22 kΩ | |
| Output current | current source < 2.5 mA | |
| Pulse length | ≥ 1 ms with external control, low active | |
| Synchronization frequency | ||
| Common mode operation | ≤ 100 Hz | |
| Multiplex operation | ≤ 71 Hz / n , n = number of sensors , n ≤ 10 | |
| Switching output | ||
| Output type | 1 push-pull output , short-circuit protected , reverse polarity protected | |
| Rated operating current | 100 mA , short-circuit/overload protected | |
| Switching frequency | factory setting: 14 Hz programmable to 33 Hz |
|
| Voltage drop | ≤ 2.5 V | |
| Repeat accuracy | ≤ ± 0.1 % of full-scale value | |
| Range hysteresis | 1 % of the adjusted operating range (default settings), programmable , min. 1 mm | |
| Off-state current | ≤ 100 µA | |
| Analog output | ||
| Output type | 1 analog output 0 (4) ... 20 mA or 1 analog output 0 ... 10 V |
|
| Resolution | current output: evaluation range [mm]/3200 but ≥ 0.35 mm voltage output: evaluation range [mm]/4000 but ≥ 0.35 mm |
|
| Deviation of the characteristic curve | ≤ ± 1 % of full-scale value | |
| Repeat accuracy | ≤ ± 0.1 % of full-scale value | |
| Load resistor | current output: ≤ 500 Ω voltage output: ≥ 1000 Ω |
|
| Compliance with standards and directives | ||
| Standard conformity | ||
| Standards | EN IEC 60947-5-2:2020 IEC 60947-5-2:2019 EN 60947-5-7:2003 IEC 60947-5-7:2003 IEC 61131-9:2013 |
|
| Approvals and certificates | ||
| UL approval | cULus Listed, Class 2 Power Source | |
| CCC approval | CCC approval / marking not required for products rated ≤36 V | |
| Ambient conditions | ||
| Ambient temperature | -25 ... 70 °C (-13 ... 158 °F) | |
| Storage temperature | -40 ... 85 °C (-40 ... 185 °F) | |
| Mechanical specifications | ||
| Connection type | Connector plug M12 x 1 , 5-pin | |
| Degree of protection | IP67 | |
| Material | ||
| Housing | stainless steel (1.4305 / AISI 303)>BR>PA, PC, POM and PBT plastic parts | |
| Transducer | epoxy resin/hollow glass sphere mixture; polyurethane foam | |
| Installation position | any position | |
| Mass | 45 g | |
| Tightening torque, fastening screws | max. 30 Nm | |
| Dimensions | ||
| Length | 90 mm | |
| Diameter | 18 mm | |
| Factory settings | ||
| Output 1 | near switch point: 50 mm far switch point: 500 mm Output mode: Window mode output behavior: NO contact |
|
| Output 2 | near limit: 50 mm far limit: 500 mm Output mode: rising ramp output behavior: Current output 4 mA ... 20 mA |
|
| Beam width | wide | |
Classifications
| System | Classcode |
|---|---|
| ECLASS 13.0 | 27272803 |
| ECLASS 12.0 | 27272803 |
| ECLASS 11.0 | 27272803 |
| ECLASS 10.0.1 | 27272803 |
| ECLASS 9.0 | 27272803 |
| ECLASS 8.0 | 27272803 |
| ECLASS 5.1 | 27272803 |
| ETIM 9.0 | EC001849 |
| ETIM 8.0 | EC001849 |
| ETIM 7.0 | EC001849 |
| ETIM 6.0 | EC001849 |
| ETIM 5.0 | EC001849 |
| UNSPSC 12.1 | 41111960 |
Details: UC500-18GS-IUEP-IO-V15
Datasheet: UC500-18GS-IUEP-IO-V15
| Datasheet | Fil type | Fil størrelse |
|---|---|---|
| Datasheet UC500-18GS-IUEP-IO-V15 | 1410 KB | |
| Fiche de données UC500-18GS-IUEP-IO-V15 | 1420 KB | |
| Datenblatt UC500-18GS-IUEP-IO-V15 | 1412 KB | |
| Hoja de datos UC500-18GS-IUEP-IO-V15 | 1422 KB |
Documents: UC500-18GS-IUEP-IO-V15
CAD+CAE: UC500-18GS-IUEP-IO-V15
| CAD | Fil type | Fil størrelse |
|---|---|---|
| CAD 3-D / CAD 3-D | STP | 3759 KB |
| CAD Portal / CAD Portal | LINK | --- |
| EPLAN | ||
| CAE EPLAN Data Portal / CAE EPLAN Data Portal | LINK | --- |
| CAE EPLAN macro EDZ / CAE EPLAN Makro EDZ | EDZ | 28 KB |
Approvals+Certificates: UC500-18GS-IUEP-IO-V15
| Certificates | Fil type | Fil størrelse |
|---|---|---|
| Canada USA UL Ordinary Location | 284 KB | |
| IO-Link Manufacturer Declaration | 140 KB | |
| Declaration of Conformity | ||
| EU Declaration of Conformity (P+F) / EU-Konformitäterklärung (P+F) | 81 KB | |
| UK Declaration of Conformity (P+F) / UK-Konformitäterklärung (P+F) | 74 KB |
Software: UC500-18GS-IUEP-IO-V15
| Device type managers (DTM) | Fil type | Fil størrelse |
|---|---|---|
| DTM (Device Type Manager) Package for UC*-18GS* ultrasonic sensors / DTM (Device Type Manager) Package für UC*-18GS* Ultraschallsensoren | ZIP | 12286 KB |
| DTM (Device Type Manager) Package for UC-PROG-IR-USB Programming Device / DTM (Device Type Manager) Package für UC-PROG-IR-USB Programmieradapter | ZIP | 9022 KB |
| IO Device Description (IODD) | ||
| IODD file for UC-18GS series / IODD Datei fuer UC-18GS Serie | ZIP | 337 KB |
| Software Tools | ||
| IO-Link Offline Parameterization Tool / IO-Link Offline-Parametriertool | ZIP | 96138 KB |
| Pepperl+Fuchs PACTware Connection Wizard (Add-In for PACTware) / Pepperl+Fuchs PACTware Connection Wizard (Add-In für PACTware) | ZIP | 320 KB |
Tilhørende produkter: UC500-18GS-IUEP-IO-V15
| Accessories | ||||||
|---|---|---|---|---|---|---|
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
|
||||||
The USi-safety ultrasonic sensor system is breaking new ground for safety applications—whether in challenging, dusty environments or in outdoor areas.
Pepperl+Fuchs offers you various downloadable documents containing knowledge on ultrasonic sensors.
Pepperl+Fuchs A/S
Kirkebjerg Allé 90
DK-2605 Brøndby
Denmark
info@dk.pepperl-fuchs.com
+45 7010 4210
© 2024 Alle rettigheder forbeholdt.
Pepperl+Fuchs er markedsledende indenfor udvikling og fabrikation af elektroniske sensorer og komponenter til det globale automatiseringsmarked. Kontinuerlig innovation, kombineret med høj kvalitet og stabil vækst har sikret uafbrudt succes gennem mere end 70 år. Pepperl+Fuchs har 6.300 ansatte på verdensplan og har produktionsfaciliteter i Tyskland, USA, Singapore, Ungarn, Indonesien og Vietnam; de fleste ISO 9001 certificerede.